Hand Forged Hammered Copper Dimmer and Light Switch Combination
Socket and Switch Sizes - Single 88mm x 88mm, Twin 148mm x 88mm
Please note ‐ These sockets and switches are individually handcrafted including the finish which means the expected delivery time is 20 to 30 working days. This can be subject to change and is not guaranteed.
Notes
Every socket and switch is made for you when you order. This means delivery times are between 20 and 30 days as we do not keep stock on the shelf.
Dimensions: Standard square plate 88 x 88mm, Standard rectangular plate 148 x 88mm, vertical rectangular plate 88 x 210mm and large square plate for 4 and 6 gang switches 148 x 148mm
What is a Dimmer and Light Switch Combination?
Light Switches and Dimmer Switches are generally available to switch 1 way and/or 2 way circuits. All of our Light Switches and Dimmers are 2 way versions and the beauty of this is that they can be used on both 1 way and 2 way circuits thus eliminating the need to buy both types. A 2 way circuit refers to a lighting point that can be switched from 2 different places i.e. Hall and Landing, where you might have a switch at the bottom of the stairs and a further switch at the top of the stairs that both control the same lighting point.
If you should have more than 2 switching positions you will require one of the switches to be an intermediate switch.
Our intelligent Dimmer range takes some of the mystery out of choosing the correct dimmer. These leading edge intelligent dimmers will adapt to the type of load put through them. This means that they will operate standard incandescent lamps as well as mains halogen lamps and low voltage halogen lamps. If you require LED lamps to be dimmed please refer to our LED Dimmer section below– these can be supplied in combination with Light Switches by request.
Our light switches and dimmer combinations are available from a double switch (Two Gang) up to 3 switches (Three Gang). The word “gang” refers to the rocker switch or dimmer– for example if you require a triple light switch it would be 3 Gang.
Larger versions of this combination range are available by request.
Our light switches have a load rating of either 10amp or 20amp and the terminals will accept up to 3 x 1.5mm Twin & Earth Cables on both the switches and the dimmers.
Our Dimmer Switches are rated by wattage. They are commonly available in 250w, 400w, 600w and 1000w modules. It is important to note that they also have a minimum load requirement of 25w, 40w, 100w and 150w respectively.
Led Dimmers
Our LED Dimmers are specifically designed to operate on ALL types of DIMMABLE LED lamps and strips. These trailing edge dimmers can be easily set to run on leading edge mode by following the instructions provided with this product. This versatility means that these LED dimmers can almost dim anything from ordinary incandescent light bulbs through to halogen bulbs as well as LED.
Non-dimmable LED lamps cannot be dimmed. Should you fit a dimmer to non-dimmable LED’s then damage to the dimmer, lamps or both will occur.
Mains voltage dimmable LED light bulbs can be dimmed using an ordinary resistive dimmer. LED lamps are an attractive proposition as they consume very low wattages and are very energy efficient. This can cause problems when choosing the correct dimmer.
If you have a few LED lamps to dim, then the total wattage will not be enough to load the dimmer. For example, four 5w LED lamps in a small room will only total 20w whilst the minimum load on a 250w dimmer is 25w. This means that the dimmer will simply not work. In these circumstances a low load dimmer rated at 5 – 50w would be required.
Under normal circumstances, so long as the minimum load is exceeded, dimming mains voltage LED lamps is not an issue so long as the minimum load is observed.
Never mix lighting types through the same dimmer on the same circuit. For example if you have 3 halogen bulbs and 3 LED bulbs fitted in the same room on the same switch you cannot replace that switch with a dimmer unless you remove either the halogen lamps or the LEDs. If you were to fit a dimmer in these circumstances then damage to the dimmer, lamps or both will occur.
On special request we can make up combined dimmers that incorporate LED dimmers and intelligent dimmers on the same plate if required.
We recommend 25mm deep wall boxes for mounting our Dimmer and Light Switch Combinations or 35mm deep wall boxes for shallow or flat plate versions.
If you require any advice or assistance please call our sales team on 01926 289 289.
Wiring Diagrams
See the wiring diagrams for One Way Light Switches and Two Way Light Switches.
Customer Reviews For Hand Forged Hammered Copper Dimmer and Light Switch Combination
No reviews yet - Be the first to Rate the Hand Forged Hammered Copper Dimmer and Light Switch Combination
Other reviews for Hand Forged Sockets & Switches are
5 stars 10
reviews
24 January 2024 by Sinead McGowan, Ballybofey - Verified Customer
08 May 2021 by Jonti, Oxford - Verified Customer
Quite Expensive But Worth It
01 April 2021 by Tom, Dorchester - Verified Customer
Not the cheapest light switches but they look so beautiful so worth every penny. The hammered dimpled finish makes the copper look distinctive from every direction. Only used in a small area but going to change over more sockets over time.
Ideal For Bathroom
19 March 2021 by Jenny D, Cheltenham - Verified Customer
Just refitted our bathroom and this was one of the finishing touches.
Ideal For Bathroom
19 March 2021 by Jenny D, Cheltenham - Verified Customer
We have just refitted our bathroom with traditional style basin, bath etc, and this is one of those finishing touches that just completes all our hard work.
Wow
14 July 2020 by Pat Bunn, Dartmouth - Verified Customer
Wow worth every penny. Seriously good stuff.
Delighted With My Purchase
03 March 2020 by Jarvis Smythe Interior Designs, London - Verified Customer
Very good quality and authentic looking product.
High Quality
03 July 2019 by John Bailey, London - Verified Customer
High Quality items and very well made. I recommend these hand made switches.
Very Well Made Items
04 March 2019 by Jackie Taylor, Kingston - Verified Customer
I found these very well made and the fronts are obviously hand-made to a very high standard. The electrical inserts made by Wandsworth are so good. They look splendid!
Stunning Design - Highest Quality
26 February 2019 by Jackson George, Dawlish - Verified Customer
These hammered switches are very well put together and my electrician says they are the best quality accessories he has ever fitted. Very authentic looking and made with real solid copper.
Dimmer and Light Switche Combinations are available in the following styles -
Art Deco , Art Deco Screwless , Burnished Flat , Executive , Executive Square , Farrow & Ball Colour Match , Georgian Premier , Grandura , Hand Forged , Heritage Flat , Jacobean Dark Oak , Jacobean Light Oak , Jacobean Medium Oak , Natural Elements , Seamless , Seamless Colour Match , Seamless Square & Ultra Square
